POR-15
Epoxy Putty - RestoGrip - StraightLine FILLERS
Application Guidelines
Below we have listed the procedure to assist you in the
application of both the POR-15 Epoxy Putty and the POR-15 RestoGrip and
Straightline Fillers ..
We hope they will be helpful ..
POR-15 Epoxy Putty :
POR-15 Epoxy Putty is an incredible epoxy putty which bridges holes in all types
of structural materials. It's so strong you can drill or tap it , yet gentle
enough that you can apply it with your bare fingers and is workable with bare
hands and mixes like clay .. SAND POR-15 Epoxy Putty after 20 minutes or
within 4 hours of application; otherwise sanding will be more difficult due to
POR-15 Epoxy's incredible density and strength.
Surface Preparation:
Remove all foreign material from surrounding areas. If any wax, oils, grease are
present, remove them with POR-15® Marine Clean (do not use solvent-based preps).
If Epoxy Putty is intended to cover rusted areas, first paint area with POR-15®
Rust Preventive Paint. Apply Epoxy Putty to POR-15® coating without sanding if
POR-15® coating is less than 6 hours old. If POR-15® coating is more than 6
hours old, sand surface lightly with 300 grit paper, then apply EPOXY PUTTY ..
For perfectly smooth finish, apply a skim coat of StraightLine Body Filler and
sand to desired result.
Application :
Step 1: Place the 2 bars side-by-side and cut what you need .. Then mix the two
parts together by hand until thoroughly blended ..
Step 2: Mix together and add a very small amount of water to reach the
consistency you desire ..
Step 3: Mix for at least one minute until both components blend into one another
..
Step 4: Apply the mixed paste to repair. The paste is useable until it begins to
harden, usually after 5 to 10 minutes.
--------------------------------------------------------------------------------
POR-15 RestoGrip Body Filler :
RestoGRIP is an exceptionally dense body filler which bridges holes in all types
of structural materials. Vacuum manufacturing insures no pinholes.
45% more flexible than other fillers. SAND RestoGRIP after 20 minutes or within
4 hours of application; otherwise sanding will be more difficult
due to RestoGRIP®’s incredible density and strength.
Surface Preparation:
Remove all foreign material from surrounding areas. If any wax, oils, grease are
present, remove them with POR-15® Marine Clean (do not use solvent-based preps).
If RestoGRIP® is intended to cover rusted areas, first paint area with POR-15®
Rust Preventive Paint. Apply RestoGRIP® to POR-15® coating without sanding if
POR-15® coating is less than 6 hours old. If POR-15® coating is more than 6
hours old, sand surface lightly with 300 grit paper, then apply RestoGRIP®. For
perfectly smooth finish, apply
a skim coat of StraightLine Body Filler and sand to desired result.
Directions for Use:
Step 1: Measure out paste and hardener. As a guide to measuring, use one
golf-ball size of filler to 3 pea-sizes of hardener.
Step 2: Mix paste and hardener together.
Step 3: Mix for one minute until both components blend into a uniform color.
Step 4: Apply the mixed paste to repair. The paste is useable until it begins to
harden, usually after 5 to 10 minutes.
--------------------------------------------------------------------------------
POR-15 StraightLine Body Filler :
POR-15 StraightLine Body Filler has over
30% more resins than other body fillers, which gives it much greater adhesion ..
This makes it the perfect product for applying over POR-15 ..It has ultra fine
particles for perfect feathering and edges and Vacuum manufacturing insures no pinholes.
StraightLine Body Filler is more flexible than other fillers. StraightLine
is ready to sand after 20 minutes or
less of application; otherwise sanding will be more difficult .. Tolerates
higher temperatures .. And is excellent for use with two-part or single part
paint systems ..
Surface Preparation:
Remove all foreign material from surrounding areas. If any wax, oils, grease are
present, remove them with POR-15® Marine Clean (do not use solvent-based preps).
If StraightLine® is intended to cover rusted areas, first paint area with
POR-15® Rust Preventive Paint. Apply StraightLine® to POR-15® coating without
sanding if POR-15® coating is less than 6 hours old. If POR-15® coating is more
than 6 hours old, sand surface lightly with 300 grit paper, then apply
StraightLine®. For perfectly smooth finish, sand to the desired result.
Directions for Use:
Step 1: Measure out paste and hardener. As a guide to measuring, use one
golf-ball size of filler to 3 pea-sizes of hardener.
Step 2: Mix paste and hardener together.
Step 3: Mix for one minute until both components blend into a uniform color.
Step 4: Apply the mixed paste to repair. The paste is useable until it begins to
harden, usually after 5 to 10 minutes.
----------------------------------------------------------------------
CAUTION !
THE ABOVE ITEMS ARE
Flammable. Contains Styrene, Cas #100-42-5.
Do not inhale. May irritate eyes and skin. Keep away from children. Keep in a
cool place. Use only in well-ventilated areas.
----------------------------------------------------------------------
Information contained herein
is to our knowledge true and accurate, but all
recommendations or suggestions are made without guarantee.
Since the conditions of its use are beyond our control, RestoMotive
Laboratories/POR-15, Inc. disclaims any liability incurred in connection
with the use of its products and information contained herein.
No person is authorized or empowered to make any statement or
recommendation not contained herein, and any such statement or
recommendation so made shall not bind the Corporation.
Furthermore, nothing contained herein shall be construed as a recommendation to
use any product in conflict with existing patents covering any material or its
use, and no license implied or in fact is granted herein under the claims of any
patents.
POR 15 INC